HPE FlexNetwork 5520 24G PoE+ 4SFP+ HI Switch (R8M28A)
- I/O ports and slots:
– (24) RJ-45 autosensing 100/1000 BASE-T ports (PoE+);
– Duplex: Ports 1–24 support 10BASE-T/100BASE-TX, 1000BASE-T (full only) Ports 17–24 support MACsec
– 4 SFP Plus 1/10G ports (SFP Plus can also support 1G SFP and 1G SFP-GE-T only works at GE.)
– (1) port expansion module slot - Additional ports and slots:
1 dual-personality RJ-45 serial console port, 1 micro-USB console, 1 out-of-band management interface, 1 USB 2.0 port
Configuration Information:
HPE FlexNetwork 5520 24G PoE+ 4SFP+ HI Switch (R8M28A) | ||
I/O ports and slots | (24) RJ-45 autosensing 100/1000 BASE-T ports (PoE+); Duplex: Ports 1–24 support 10BASE-T/100BASE-TX, 1000BASE-T (full only) Ports 17–24 support MACsec |
|
4 SFP Plus 1/10G ports (SFP Plus can also support 1G SFP and 1G SFP-GE-T only works at GE.) |
||
(1) port expansion module slot | ||
Additional ports and slots | 1 dual-personality RJ-45 serial console port, 1 micro-USB console, 1 out-of-band management interface, 1 USB 2.0 port |
|
Physical characteristics | Dimensions | 44 cm (w) x 36 cm (d) x 4.36 cm (h) |
Weight | ≤ 9.2 kg | |
Memory and processor | 2 GB SDRAM; packet buffer size: 4 MB, 512 MB flash |
|
Mounting and enclosure | Mounts in an EIA standard 19 inch telco rack or equipment cabinet (hardware included) |
|
Performance | IPv6 Ready Certified | |
1000 Mb Latency | < 5 µs | |
10 Gbps Latency | < 3 µs | |
Throughput | 180 Mpps | |
Routing/Switching capacity | 288 Gbps | |
Static MAC table | 1K | |
MAC address table size | Up to 64K, recommended 32K | |
Environment | Operating temperature | 23°F to 113°F (–5°C to 45°C) |
Operating relative humidity | 5% to 95%, noncondensing | |
Non-operating/Storage temperature | -40°F to 158°F (-40°C to 70°C) | |
Non-operating/Storage relative humidity | 5% to 95%, noncondensing | |
Acoustic | 68.9 dB ISO 7779 | |
Electrical characteristics |
Frequency | 50/60 Hz |
Maximum heat dissipation | Ranges from 105 BTU/hr to 3166 BTU/hr depending on power supply configuration |
|
Voltage | 90 – 264 VAC
–36 VDC to 72 VDC |
|
Current | 3A | |
Maximum power rating | 1110W | |
Idle power
PoE power |
31 W
720W PoE+ |
|
Notes: | • Idle power is the actual power consumption of the device with no ports connected. • Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. • PoE+ power range is from 450W to 1440W. PoE+ power is the power supplied by the internal power supplies. It is dependent on the type and quantity of power supplies. The device supports 1 or 2 internal modular power supplies. • DC maximum input current is 6A. Voltage range for power modules PSR360-56A: 6-3A, PSR720-56A:10-5A, PSR1110-56A: 12-6A |
|
Safety | UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; IEC 62368-1; CAN/CSA-C22.2 No. 60950-1; EN 62368-1/A11; FDA 21 CFR Subchapter J; RoHS Compliance |
|
Emissions |
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN 61000-3-3:2008; VCCI V-3/2012.04; EN 61000-3-2:2006+A1:2009+A2:2009; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A |
|
Immunity | Generic | EN 55024 |
ESD | EN 300 386 | |
Management | HPE IMC; command-line interface; SNMP manager |
|
Services | See the Hewlett Packard Enterprise website at hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, contact your local HPE sales office. |
Datasheet HPE FlexNetwork 5520 24G PoE+ 4SFP+ HI Switch (R8M28A)
Ryker (xác minh chủ tài khoản) –
Good service.
Paul (xác minh chủ tài khoản) –
The product is firmly packed.
Nguyễn Phạm Phương Oanh –
Hàng chính hãng giá lại rẻ